|
 There
are many classifications of muds or drilling fluid systems, including
water-based, oil based, emulsion and air or gas-based. Oil-based
drilling muds show improvements over standard water muds in the
areas of increased drilling rate and bit life, reduction in hole
problems, reduction in torque, less sticking of pipe, and less hole
enlargement. Special emulsifiers and additives are used in
these drilling fluid systems to provide a host of functions, including
emulsification, oil wetting, viscosity & fluid loss controls.
Mobile
Rosin Oil Company has been manufacturing and supplying emulsifiers
for the Oilfield Industry since 1999. Below is a list of our
basic products serving this industry. You will find Typical
Data sheets as well as MSDS which are downloadable
in (.pdf) format. If you are unable to download
and read the documents, you may download a free reader here:
For
further information or direct technical assistance regarding our
products, please contact Jalandar Y. Jadhav, Ph.D. at jyj@mobros.com.
| PINEMUL®100 |
|
A
100% active, oil-soluble viscous liquid comprised of modified
and oxidized tall oil that functions as a primary
emulsifier in invert (water-in-oil) drilling fluids.
It provides good emulsification, higher electrical stability
with filtrate control properties. Normally used at 5-7
lbs/barrel rate. Lime is required to activate.
PINEMUL
100 Typical Data PINEMUL
100 MSDS |
| |
|
|
| PINEMUL®101 |
|
A
lower viscosity liquid, 100% active material based on modified
tall oil chemistry that functions as primary emulsifier
in invert drilling fluids. It provides good emulsification
and higher electrical stability with some filtrate control
properties. Normally used at 5-7 lbs/barrel rate.
Lime is required to activate.
PINEMUL
101 Typical Data PINEMUL
101 MSDS |
| |
|
|
| PINEMUL®102 |
|
A
100% active, oil-soluble, viscous liquid based on uniquely
modified fatty acids and resins that functions as filtrate
reducer in oil-based invert mud systems. It
also provides good emulsification and higher electrical stability.
Normally used at 2-4 lbs/barrel rate. Product can be
diluted with crude oil, hydrocarbon solvents or synthetic
oils.
PINEMUL
102 Typical Data PINEMUL
102 MSDS |
| |
|
|
| PINEMUL®200 |
|
A
viscous liquid, 80-90% active modified alkyl polyamide in
mineral oil that functions as emulsifier and wetting
agent in oil-based drilling muds. Normally
used at a 2-4 lbs/barrel rate in combination with primary
emulsifiers. Product can be diluted with crude oil,
hydrocarbon solvents or synthetic oils.
PINEMUL
200 Typical Data PINEMUL
200 MSDS |
| |
|
|
| PINEMUL®201 |
|
A
lower viscosity, 67-72% active modified alkyl polyamide in
naphthenic oil that functions as emulsifier and wetting
agent in oil-based drilling muds. Normally
used at a 3-5 lbs/barrel rate. Product can be diluted
with base fluid to make desired field strength formulation.
PINEMUL
201 Typical Data PINEMUL
201 MSDS |
| |
|
|
| PINEMUL®300 |
|
A
97-100% active viscous liquid comprised of modified polyamide
and tall oil that functions as emulsifier and wetting
agent in oil-based drilling muds. Provides
excellent emulsification, high electrical stability and desired
filtrate control. Lime is required to activate.
Normally used at a 7-8 lbs/barrel rate. Product can
be diluted with base fluids to make desired field strength
formulation.
PINEMUL
300 Typical Data PINEMUL
300 MSDS |
| |
|
|
| PINEMUL®302 |
|
A
lower viscosity, 67-72% active liquid comprised of modified
polyamide in naphthenic oil that functions as emulsifier
and wetting agent in oil-based drilling muds.
Provides excellent emulsification, high electrical stability
and desired filtrate control. Lime is required to activate.
Normally used at a 7-8 lbs/barrel rate. Product can
be diluted with base fluids to make desired field strength
formulation.
PINEMUL
302 Typical Data PINEMUL
302 MSDS
|
*PINEMUL
Trademark Application Pending - Serial No. 78464338*
|
